Version 2.153 Toolpath Editor deletes program if empty. Toolpaths with Euorpean Errors are corrected. Version 2.152 Analayse remembers position. Version 2.151 Small move rounding arcs of less than 2 x Chaining Tolerance are removed. BackplotWithDecimalPlaces=0 added to [ToolPathType] in .INI If <> 0 then Backplot values are rounded to number of Decimal Places set. Version 2.150 Fixed initial directories Version 2.142 Decimal Point allowed in filenames. DXF Import Zero length Text not allowed. HomeMoveOff added to [ToolPathType] in .INI Pocketing allows for small chain error. Version 2.141 Last tool is set when original toolpath is used. Tool picture in New Pocketing corrected. Version 2.140 Directory Paths Allowed. File New and Open check for changes. Toolpath Arrange Auto Scrolls when moving path. Toolpath Arrange loads Grid style editor for paths > 169 Save and Load Text has rotation angle stored. Change Directory Hidden in Backplot. Dimension text location uses Grid state. Copy/Move picture changed to correct style. Filename preserved when using CTRL + S. Toolpath arrange not allowed during backplot. Version 2.131 DXF allows for Block Names with Spaces. Sharp Corner intersections corrected. Version 2.130 Vista Compatible CTRL + R Redraws with highlight Curve Fit by Cubic Spline on chain of points added. Subroutine ability added for pocketing. Version 2.125 CDLTrace.dll modified for decimal comma values. Translation of X and Y moved to text(13) and text(14) Import allows for Toolpath files. Offset changed to make arcs > tool rad into lines when using sharp in profile. Auto Layout filter changed for .pst, .cnk & .lnk Version 2.124 Black letters on Circle OK Thread Milling direction output corrected. AutoLayout allows for maximum elements exceeding 16000. Path number added to Backplot. In [Options] use NoAddPath=1 to remove. Delete cancels selection. Version 2.123 Toggle line style applies to chain Version 2.122 Corrected missing fonts after directory change. Save/load Grid value on exit/entry Version 2.121 Printers bigger than A4 allowed. Added help to and for New Pocketing. Version 2.120 19/01/2006 New HaspVB32.dll used Printer copies added Output DXF Header added to Settings form. Drill Wizard added to Drill form Spiral Pocket gets Slope if 'Out' is selected in Pocket Preview Spiral Pocket gets Climb Milling Spiral Pocket released Allow3D in Mill and Sweep for Autoform (follows Z value from geometery) Version 2.118 14/10/05 Save DXF output full header. Command line file loaded according to extension. Version 2.117 18/07/05 Overwrite corrected in NewPocketing Repeat with new edge allowance added to new pocketing (Stepover = 0 if yes) Version 2.116 Save as updates Title with the new filename Layer Names Preserved on DXF Load Version 2.115 Backplot Tool position corrected Set Datum removes file chains Version 2.114 DXF Import, Circles increments count Version 2.113 Backplot stores the file plotted for the Post Processor unless NotPostOut=1 under [Options] in Ini Backplot Solid Outline colour changed to Darkgray. Spiral Pocket allows file import. Version 2.112 DXF files with Numerical Layer Values loaded as Layer Numbewr Mod 10 Toolnumber reset to current number not picture after backplot Machining Fonts checks directory exists. Version 2.111 Save DXF gets File Header. Redraw added to window resize. Added functiionality for New Pocketing. Version 2.106 Added 'By Point' to xForm Layer Colour used when loading Shape Version 2.105 07/10/04 Pocket step multiplier changed for Zero lines. Version 2.104 Corrected [Options] ChangeDirectory spelling. Straight line tolerence tightend. Minimum Zoom changed from 0.001 to 0.0001 allowing for 500000 rads. Save Geometry corrected when last layer name is 'TEXT'. Toolselection picture corrected. G84 gets Pitch (stored as Peck) parameter for time calculation. Version 2.103 TagHeight added to [ToolPathMill] secion of INI file. Added Tag concept. If StopBeforeMove=2 then any Tag in the profile will have TagHeight added to it's depth on the last Pass. Version 2.102 Allow Comp Off in Pocketing. Added check for Revolve Crossover and switch (Swap) to reverse check side. Version 2.101 Zero radius circle on Load Geo with CHAIN prevented ExpandPecking like Geometry CDL-V3 implemented Set Stop added; use AllowStop=1 in [ToolPathMill] section of .ini file. if Entry Exit modifier is zero entry lines are not swapped when longer than circle rad. Version 2.100 19/03/04 Enabled Windows XP Theme Taper changed from Long to Variant Fonts settings saved. Circular Pocket Diameter is output instead of Index Circular and Rectangular Pockets use Variable input Export DXF corrected. Write Chain added. Version 2.037 Break does not change layer or colour. Arc Line Arc corrected for duplicate centres. Import dialog remembers last filter used. Leaving Index angle blank will not cause Standard Pockets to fail Burn and Wire: Machining Fonts get Select Point option. Post Processor: Modified for 'last feed' problem Version 2.036 Added 'Taper Angle' to Tread Milling. Post Processor v1.17 changed to suit. Layers (tool number) supported in Import of '.pst' files Version 2.035 Invisible Tools > 8 do not draw spurious lines Delays when importing .pst with drilling file removed if Index is called then a Redraw is completed. Version 2.034 Lines Horizontal and Vertical where the first point is sketched have the focus in value. Fixed Slope in pocket to restart at each depth. Version 2.032 Redim for Toolpath allows extra dimension Move with multiple repetitions made an Error Picking chain of small lines allows Offset and Reverse Export can Write Chains and Import can Read them Check for bad milling Entry/Exit ignored if tool diameter is zero Rectangular Pocket does Slot if Width and Radius = Cutter. Version 2.031 Dimensioning disabled in ISO, not the whole menu! Standard Pockets use the correct program number. Version 2.030 Collision checking in Sweep improved. Trimming in Sweep corected to allow for the Rotation Centre. Version 2.019 Added CTRL + G create group All Added CTRL + C create group Lines/Arcs Point End Point ignores Mid Point Icon Chained geometry files import as chain not group Added WaitMouseUp under [Options] for Zoom function. Check for Collision in Sweep Version 2.018 Export DXF ouputs CIRCLE for full arcs. DXF Initial Layers selected. Delete duplicates 'Using Smart method' improved for arcs. Revolve works with single entity again. In Taper Milling with failed line/arc intersections, the arc's are removed. Version 2.017 Delete Current Geometry calls DeleteAllChains to re-assign groups. DXF notifies number of Unsupported Splines & 3DSolids. DXF Imports Unsupported Polyline Vertexes as Lines in a Group. DXF Imports Unsupported Spline XYZ co-ordinates as Points in a Group. Revolve allows Edge Allowance again. Version 2.016 Maximum chains checked Toolpath Editor gets Path Number in Comment X value in BASEPOINT for DXF corrected. Scale supported in DXF input. Complete Non ASCII DXF files imported. Entry rad checking improved for lines and arcs New INI option under [ToolPathMill], AllowToolBarChange=0 New INI option under [ToolPathMill], AllowCheckEntry=0 Version 2.015 Trap for Arc Arc intersection failure in toolpath added. Version 2.014 Swap ZX changed to Rotate Z with Axis and Angle selectable. Swap ZX enabled for Professional level Analyse outputs Z if not Zero. Fixed VB Dir$ bug. Version 2.013 Analyse window cannot be below the screen visible area. Pocket Wizard uses correct feedrates Sweep shows tool path centre line on cross section. Version 2.012 Repeat with new edge allowance is not called when comp is off. Sweep uses Ball Rad for offset in place of Tool Rad. Ballrad cancel aborts operation. Version 2.011 Pocket Wizard does not call 'Repeat Drill' after machining. Version 2.010 Added C-Axis milling for 4th Axis Rotary translation of Y axis. Modified entry corner checking to allow for Corner Rounding version 2.008 Sweep Ball Radius for flat bottom tools corrected. Auto Layout does not save initial geometry. 2.007 View cannot be changed during Backplot. Peck in Taper profile corrected. Peck and Dwell are set to zero when not used in the cycle selected. Revolve functions again. (V2.006 Trimmimg plane problem) Bad dimensional position fixed. Invisible layers do not hide backplot. Tool Show/Hide selections reset for new file. 2.006 In Sweep if Triming Plane is set to 'N', 'n' or blank it is ignored. Thread Milling corrected where Tool diameter is not zero. Incorrect number of pecks fixed in Pocketing. Chain recall order for NTFS fixed. 2.005 Directory function fixed in machining. 2.004 AutoLayout fixed 2.003 Coolant On/Off consitant with selection. Heiden.cfg supports Feedrates in Z 2.002 Filename in Graphics print placed outside of printed drawing. Graphic tool display speed increased at tool change. 2.001 Filename is Printed in Graphics if NoPrintHeaders=0 Page description is Printed in Edit if NoPrintHeaders=0 2.00 04/03/02 Security Changed. 'View XY' and 'View ISO' added to Popup menu. Pockets without Hatching are machined. HideMenus=1 in INI file will remove any menu item with a blank caption. Sweep gets "Ball Radius" question to allow for flat bottom tools. Sweep Entry/Exit corrected for Compensation Right. Milling gets Slope with first move if no compensation and first move is a line and start = end. Autoform input remembers settings In Swept, Profile and cross section are reversed. File Save and Toolpath Save both now use ".geo" Printer and Orientation box added to Print Menu. Corrected Delete Material. Corrected Double Click in Comment box for Rough, Hand etc. 1.50 User Login implemented when AllowPathChanges=1 The correct folders are selected in Settings when AllowPathChanges=1 Tool buttons cannot be customised.